This enables the Pi to be driven remotely and set up from a PC and also to take advantage of copy and paste of the text listed here. Etcher is free and downloadable from and is straightforward to run:Īfter the card has been flashed add a blank file called ‘SSH’ to ‘Boot’. Then run Etcher to download the image to an SD card. The version available at the time of writing was October 2018 but others should work fine. The process will use remote setup of the Pi as in most cases this is easier – and can avoid the need for a keyboard.įirst download Raspbian Stretch or Stretch Lite from The latter uses less memory but the former may be needed if the PI is being used for something else as well. The system will work from both the full Raspbian Stretch install and from Stretch Lite. Text in bold italics has to be entered during the setup and can in most cases be copied and pasted – that saves a load of time. The instructions here should allow a novice (or more experienced) to get this running from scratch. See: instructable This has the big plus of being thin and being able to fit into a real picture frame.Īll the software/firmware required is free. Lastly there is the option of re-purposing the screen from a dead laptop.I picked up a good condition 22” IPS, full HD (1920x1080) Iiyama touch screen monitor for under £80 delivered. If they don’t have a HDMI input they are very likely to have DVI that can be used via an adaptor or HDMI to DVI lead. Used ones are available at low cost on ebay. A downside of these is that the connectors plug into the side – that looks untidy or requires a wide frame to hide. A touch screen is not a requirement here but might be useful when this is the screensaver for another application. Waveshare do very good monitors for the Pi, including ones with touch screens.I could have used a ZeroW (WiFi) but for the same cost one can get a Zero plus a 2 port USB hub and use a WiFi dongle to optimise the aerial location. For example, this could be the screensaver for a Pi based media controller or for an interface to my Pi based music and radio player.įor simplicity and size I have used a Pi Zero here but any of the Pi’s should work. This can be a standalone digital picture frame or can be the screensaver for a Pi based system (doing something else) and show pictures when it is not being used. You can also transfer photos direct from a mobile phone (e.g. It can be powered by the tiny £4.50 Pi Zero. This is a very easy and low cost route to a digital photo frame – with the advantage of adding /removing photos over WiFi via ‘click and drag’ using a (free) file transfer program. Does something like that already exist? Or is it something I could look into making? Before I start digging into APIs and docs I want to make sure I'm not reinventing the wheel.Raspberry Pi Digital Photo Picture Frame - WiFi Linked My question is, has anyone looked into integrating this into something like xscreensaver? Or is there an existing package that I've overlooked? I'm looking for something that will be available out-of-the-box that could integrate into the GUI and be accessible through settings etc.Ī custom plugin for xscreensaver would be one possible solution. This works great when launched as a process on startup, but. It's a tiny piece of C code that listens on /dev/input/event0 and turns the backlight off if no input has been detected for x seconds. I want the screen to turn off after a set amount of inactivity, then wake up when I touch a key/move the mouse etc, like a screensaver.Īfter a bit more searching I found this: I've found the Pi Python script that's been floating around ( ) and while it does work, I'm only able to automate the process through a cronjob, which means no wake-on-input. I picked up the official RPF 7" touchscreen ( ) and am looking at power saving solutions. In that case, please feel free to move/archive this thread and point me in the right direction. I've done a bit of trawling on the forums and some repos but I might have missed something. I apologise if this has been discussed already.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |